BZSMX - CAUSTIC SODA, LYE, SODIUM HYDRATE, SX0595
- MSDS: BZSMX
- Manufacturer: EM SCIENCE
- Product Name: CAUSTIC SODA, LYE, SODIUM HYDRATE, SX0595
- National Stock Number: 6810-00N069983
Product Identification
Product ID:CAUSTIC SODA, LYE, SODIUM HYDRATE, SX0595
MSDS Date:02/06/1993
FSC:6810
NIIN:00N069983
MSDS Number: BZSMX
Responsible Party
GIBBSTOWN, NJ 08027
US
Emergency Phone: 800-424-9300(CHEMTREC)
Info Phone: 609-354-9200
Cage: DO242
Contractor
Telephone: 800-424-9300 (CHEMTREC)
Cage: DO242
Ingredients
SODIUM HYDROXIDE (CERCLA)
CAS: 1310-73-2
RTECS: WB4900000
Fraction By Weight: 100%
OSHA PEL 2 MG/M3
ACGIH TLV: 2 MG/M3, C
EPA Report Quantity: 1000 LBS
DOT Report Quantity: 1000 LBS
SHOULD BE IMPLEMENTED TO REDUCE EXPOSURE.
RTECS: 9999999ZZ
WHEN HANDLING THIS MATERIAL. SAFETY
RTECS: 9999999ZZ
& FULL LENGTH FACESHIELD .
RTECS: 9999999ZZ
Hazards
LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:EXTREMELY TOXIC & CORROSIVE. CAUSES
SEVERE BURNS ON CONTACT W/BODY TISSUE. VAPOR IRRITATING TO EYES &
RESPIRATORY PASSAGES. TESTS ON LABORATORY ANIMALS INDICATE MATERIAL
MAY PRODUCE ADVERSE MUTAGENIC EFFECTS. CITED IN RTECS.
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:DATA NOT AVAILABLE.
First Aid
First Aid:GET MEDICAL ASSISTANCE FOR ALL CASES OF OVEREXPOSURE.
SKIN:IMMEDIATELY FLUSH THORO W/LARGE AMOUNTS OF WATER. REMOVE
CONTAMINATED CLOTHING & WASH BEFORE REUSE. EYES:IMMEDIATELY FLUSH
THORO W/WATER FOR AT LEAST 15 MINUTES. INHAL:REMOVE TO FRESH AIR;
GIVE ARTF RESP IF BREATHING HAS STOPPED. INGEST:DO NOT INDUCE
VOMITING; IF CONSCIOUS, GIVE WATER FREELY & GET MEDICAL ATTENTION.
Fire Fighting
Flash Point:NONCOMBUSTIBLE
Extinguishing Media:FLOOD W/WATER, USING CARE NOT TO SPLATTER OR SPLASH
MATERIAL.
Fire Fighting Procedures:USE NIOSH/MSHA APPROVED SCBA & FULL PROTECTIVE
EQUIPMENT .
Unusual Fire/Explosion Hazard:CAN REACT W/CERTAIN METALS (AL, SN, MG,
CU, ETC) TO RELEASE EXPLOSIVE HYDROGEN GAS.
Accidental Release
Spill Release Procedures:EVACUATE AREA OF ALL UNNEC PERS. WEAR SUITABLE
PROT EQUIP LISTED UNDER EXPOS/PERSONAL PROT SECTION. ELIM ANY IGNIT
SOURCES UNTIL AREA IS DETERMINED TO BE FREE FROM EXPLO/FIRE HAZS.
CONTAIN RELS & ELIM ITS SOURCE, IF THIS CAN BE DONE W/OUT (SUPP
DATA)
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.
Handling
Handling and Storage Precautions:DO NOT BREATHE DUST/VAP. STORE IN DRY,
WELL-VENTED AREA AWAY FROM ACID, METALS, EXPLOIVES, ORG PEROXIDES &
EASILY IGNITABLE MATLS.
Other Precautions:KEEP CNTNR TIGHTLY CLSD. WHILE MAKING SOLN ADD SLOWLY
TO SURF OF SOLN TO AVOID VIOLENT SPLATTERING. DO NOT GET IN EYES,
ON SKIN/ON CLTHG. RETAINED RESIDUE MAY MAKE EMPTY CNTNRS HAZ; USE
CAUT. DO NOT T AKE INTERNALLY.
Exposure Controls
Respiratory Protection:IF WORKPLACE EXPOS LIM(S) OF PROD/ANY COMPONENT
IS EXCEEDED, NIOSH/MSHA APPRVD AIR SUPPLIED RESP IS ADVISED IN
ABSENCE OF PROPER ENVIRON CONTROL. OSHA REGS ALSO PERMIT OTHER
NIOSH/MSHA APPRVD RESPS (N EG PRESS TYPE) UNDER SPECIFIED (SUPDAT)
Ventilation:MATERIAL SHOULD BE HANDLED OR TRANSFERRED IN AN APPROVED
FUME HOOD OR W/ADEQUATE VENTILATION.
Protective Gloves:NITRILE OR EQUIVALENT GLOVES.
Eye Protection:ANSI APPROVED CHEM WORKERS GOGGS (ING 4)
Other Protective Equipment:EYE WASH FOUNTAIN & DELUGE SHOWER WHICH MEET
ANSI DESIGN CRITERIA . PROT CLTHG (IMPERVIOUS) SHOULD BE WORN (ING
3)
Work Hygienic Practices:WASH THOROUGHLY AFTER HANDLING.
Supplemental Safety and Health
SPILL PROC:RISK. TAKE UP & CONTAINERIZE FOR PROPER DISP AS DESCRIBED
UNDER DISP SECTION. COMPLY W/FED, STATE & LOC REGS ON REPORTING
RELS. RQ: SODIUM HYDROXIDE - 1000 LBS. REFER TO REGULATORY INFO FOR
OTHER REGULATORY DATA. RESP PROT:CNDTNS (SEE YOUR SAFETY EQUIP
SUPPLIER). ENGINEERING &/OR ADMIN CONTROLS (ING 2)
Chemical Properties
Boiling Pt:B.P. Text:2534F,1390C
Melt/Freeze Pt:M.P/F.P Text:605F,318C
Spec Gravity:2.13 (H*2O=1)
Solubility in Water:SOLUBLE
Appearance and Odor:WHITE, DELIQUESCENT PELLETS, FLAKES OR GRANULES;
ODORLESS.
Stability
Stability Indicator/Materials to Avoid:YES
WATER, ACIDS, CHLORINATED HYDROCARBONS, METALS, ORGANIC MATERIALS.
Stability Condition to Avoid:CONTACT W/MOISTURE MAY GENERATE SUFFICIENT
HEAT TO IGNITE SURROUNDING COMBUSTIBLE MATERIAL.
Hazardous Decomposition Products:NONE INDICATED.
Disposal
Waste Disposal Methods:MATL DOES NOT HAVE EPA WASTE NUMBER & IS NOT A
LISTED WASTE, HOWEVER CONSULTATION W/PERMITTED WASTE DISP SITE
(TSD) SHOULD BE ACCOMPLISHED. ALWAYS CONT A PERMITTED WASTE
DISPOSER (TSD) TO ASSURE COMPL IANCE W/ALL CURRENT LOC, STATE & FED
REGS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.